 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ICX424AQ Diagonal 6mm (Type 1/3) Progressive Scan CCD Image Sensor with Square Pixel for Color Cameras Description The ICX424AQ is a diagonal 6mm (Type 1/3) interline CCD solid-state image sensor with a square pixel array which supports VGA format. Progressive scan allows all pixels signals to be output independently within approximately 1/60 second. This chip features an electronic shutter with variable charge-storage time which makes it possible to realize full-frame still images without a mechanical shutter. High sensitivity and low dark current are achieved through the adoption of the HAD (Hole-Accumulation Diode) sensors. This chip is suitable for applications such as FA and surveillance cameras. Features * Progressive scan allows individual readout of the image signals from all pixels. * High vertical resolution still images without a mechanical shutter * Square pixel * Supports VGA format * Horizontal drive frequency: 24.54MHz * No voltage adjustments (reset gate and substrate bias are not adjusted.) * R, G, B primary color mosaic filters on chip * High resolution, high color reproductivity, high sensitivity, low dark current * Continuous variable-speed shutter * Low smear * Excellent anti-blooming characteristics * Horizontal register: 5.0V drive * 16-pin high precision plastic package (enables dual-surface standard) 16 pin DIP (Plastic) Pin 1 2 V 8 2 Pin 9 H 31 Optical black position (Top View) Device Structure * Interline CCD image sensor * Image size: Diagonal 6mm (Type 1/3) * Number of effective pixels: 659 (H) x 494 (V) approx. 330K pixels * Total number of pixels: 692 (H) x 504 (V) approx. 350K pixels * Chip size: 5.79mm (H) x 4.89mm (V) * Unit cell size: 7.4m (H) x 7.4m (V) * Optical black: Horizontal (H) direction: Front 2 pixels, rear 31 pixels Vertical (V) direction: Front 8 pixels, rear 2 pixels * Number of dummy bits: Horizontal 16 Vertical 5 * Substrate material: Silicon Wfine CCD is trademark of Sony corporation. Represents a CCD adopting progressive scan, primary color filter and square pixel. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E01Z29A25-PS ICX424AQ Block Diagram and Pin Configuration (Top View) VOUT GND GND CGG V1 V2 2 B G B G B G Note) V3 1 NC 4 B G B G B G 8 7 6 5 3 G Vertical register R G R G R G R G R G R Horizontal register Note) 9 VDD 10 SUBCIR 11 GND 12 SUB 13 VL 14 RG 15 H1 16 H2 : Photo sensor Pin Description Pin No. Symbol 1 2 3 4 5 6 7 8 V3 V2 V1 NC GND CGG GND VOUT GND Output amplifier gate1 GND Signal output Description Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock Pin No. Symbol 9 10 11 12 13 14 15 16 VDD SUBCIR GND SUB VL RG H1 H2 Description Supply voltage Supply voltage for the substrate voltage generation GND Substrate clock Protective transistor bias Reset gate clock Horizontal register transfer clock Horizontal register transfer clock 1 DC bias is applied within the CCD, so that this pin should be grounded externally through a capacitance of 1000pF. -2- ICX424AQ Absolute Maximum Ratings Item Substrate clock SUB - GND Supply voltage Clock input voltage VDD, VOUT, CGG, SUBCIR - GND VDD, VOUT, CGG, SUBCIR - SUB V1, V2, V3 - GND V1, V2, V3 - SUB Ratings -0.3 to +36 -0.3 to +18 -22 to +9 -15 to +16 to +10 to +15 to +16 -16 to +16 -10 to +15 -55 to +10 -65 to +0.3 -0.3 to +27.5 -0.3 to +20.5 -0.3 to +17.5 -30 to +80 -10 to +60 -10 to +75 Unit V V V V V V V V V V V V V V C C C 2 Remarks Voltage difference between vertical clock input pins Voltage difference between horizongal clock input pins H1, H2 - V3 H1, H2 - GND H1, H2 - SUB VL - SUB V2, V3 - VL RG - GND V1, H1, H2, GND - VL Storage temperature Performance guarantee temperature Operating temperature 2 +24V (Max.) when clock width < 10s, clock duty factor < 0.1%. +16V (Max.) is guaranteed for power-on and power-off. -3- ICX424AQ Bias Conditions Item Supply voltage Protective transistor bias Substrate clock Reset gate clock Symbol VDD VL SUB RG Min. 14.55 Typ. 15.0 1 2 3 Max. 15.45 Unit V Remarks 1 VL setting is the VVL voltage of the vertical transfer clock waveform, or the same voltage as the VL power supply for the V driver should be used. 2 Set SUBCIR pin to open when applying a DC bias to the substrate clock pin. 3 Do not apply a DC bias to the reset gate clock pins, because a DC bias is generated within the CCD. DC Characteristics Item Supply current Symbol IDD Min. Typ. 7 Max. 9 Unit mA Remarks Clock Voltage Conditions Item Readout clock voltage VVT VVH02 VVH1, VVH2, VVH3 VVL1, VVL2, VVL3 VVL1, VVL2, VVL3 Vertical transfer clock voltage V1, V2, V3 | VVL1 - VVL3 | VVHH VVHL VVLH VVLL VH Horizontal transfer clock voltage VHL VCR VRG Reset gate clock voltage VRGLH - VRGLL VRGL - VRGLm Substrate clock voltage VSUB 21.5 22.5 4.75 -0.05 0.8 4.5 5.0 0 2.5 5.0 5.5 0.8 0.5 23.5 Symbol Min. 14.55 -0.05 -0.2 -7.8 -8.0 6.8 Typ. 15.0 0 0 -7.5 -7.5 7.5 Max. Unit 15.45 0.05 0.05 -7.2 -7.0 8.05 0.1 1.0 2.3 1.0 1.0 5.25 0.05 V V V V V V V V V V V V V V V V V V Waveform Diagram 1 2 2 2 2 2 2 2 2 2 2 3 3 3 4 4 4 5 Low-level coupling Low-level coupling Cross-point voltage High-level coupling High-level coupling Low-level coupling Low-level coupling VVL = VVL1 (VVL3)/2 (During 24.54MHz) VVL = VVL1 (VVL3)/2 (During 12.27MHz) VVH = VVH02 Remarks -4- ICX424AQ Clock Equivalent Circuit Constants Item Symbol CV1 Capacitance between vertical transfer clock and GND CV2 CV3 CV12 Capacitance between vertical transfer clocks CV23 CV31 Capacitance between horizontal transfer clock and GND CH1, CH2 Capacitance between horizontal transfer clocks Capacitance between reset gate clock and GND Capacitance between substrate clock and GND Vertical transfer clock series resistor Vertical transfer clock ground resistor Horizontal transfer clock series resistor Reset gate clock series resistor CHH CRG CSUB R1, R2 R3 RGND RH1, RH2 RRG Min. Typ. 3900 3300 3300 1000 1000 1000 47 30 6 560 33 18 100 10 39 Max. Unit pF pF pF pF pF pF pF pF pF pF Remarks V1 R1 CV12 CV1 RGND CV31 CV3 CV23 CV2 R2 V2 RH1 H1 CHH CH1 CH2 RH2 H2 R3 V3 Vertical transfer clock equivalent circuit Horizontal transfer clock equivalent circuit RG RRG CRG Reset gate clock equivalent circuit -5- ICX424AQ Drive Clock Waveform Conditions (1) Readout clock waveform VT 100% 90% M VVT 10% 0% tr twh tf 0V M 2 Note) Readout clock is used by composing vertical transfer clocks V2 and V3. (2) Vertical transfer clock waveform V1 VVHL VVH1 VVHH VVH VVLH VVL01 VVL1 VVLL V2 VVH02 VVHH VVHL VVH2 VVH VVL VVLH VVL2 VVLL V3 VVHL VVH3 VVHH VVH VVL VVL03 VVLL VVLH VVL VVH = VVH02 VVL = (VVL01 + VVL03)/2 VVL3 = VVL03 -6- VV1 = VVH1 - VVL01 VV2 = VVH02 - VVL2 VV3 = VVH3 - VVL03 ICX424AQ (3) Horizontal transfer clock waveform H1, H2 tr twh tf H2 90% VCR VH twl VH 2 10% H1 two VHL Cross-point voltage for the H1 rising side of the horizontal transfer clocks H1 and H2 waveforms is VCR. The overlap period for twh and twl of horizontal transfer clocks H1 and H2 is two. (4) Reset gate clock waveform RG tr twh tf VRGH RG waveform twl VRG Point A VRGLH VRGLL VRGLm VRGL VRGLH is the maximum value and VRGLL is the minimum value of the coupling waveform during the period from Point A in the above diagram until the rising edge of RG. In addition, VRGL is the average value of VRGLH and VRGLL. VRGL = (VRGLH + VRGLL)/2 Assuming VRGH is the minimum value during the interval twh, then: VRG = VRGH - VRGL Negative overshoot level during the falling edge of RG is VRGLm. (5) Substrate clock waveform SUB 100% 90% M VSUB 10% VSUB 0% (A bias generated within the CCD) M 2 tf tr twh -7- ICX424AQ Clock Switching Characteristics (Horizontal drive frequency: 24.54MHz) twh Item Readout clock Vertical transfer clock Horizontal transfer clock Symbol VT V1, V2, V3 H1 H2 10.5 14.6 10.5 14.6 6 8 10.5 14.6 10.5 14.6 25.8 6.4 10.5 6.4 10.5 4 0.5 twl tr tf Unit s 250 6.4 10.5 6.4 10.5 3 0.5 ns ns ns s During drain charge Remarks During readout When using CXD3400N tf tr - 2ns Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. 2.3 2.5 0.5 15 0.5 Reset gate clock RG Substrate clock SUB 0.75 0.9 Item Horizontal transfer clock Symbol H1, H2 two Min. Typ. Max. 10.5 14.6 Unit ns Remarks 1 Clock Switching Characteristics (Horizontal drive frequency: 12.27MHz) twh Item Readout clock Vertical transfer clock Horizontal transfer clock Symbol VT V1, V2, V3 H1 H2 24 30 25 31.5 25 30 62.5 10 17.5 10 3 0.5 15 26.5 31.5 11 13 twl tr tf Unit s 350 10 17.5 10 3 0.5 15 ns ns ns s During drain charge Remarks During readout When using CXD3400N tf tr - 2ns Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. 4.6 5.0 0.5 15 0.5 Reset gate clock RG Substrate clock SUB 1.5 1.8 Item Horizontal transfer clock Symbol H1, H2 two Min. Typ. Max. 21.5 25.5 Unit ns Remarks 1 1 The overlap period of twh and twl of horizontal transfer clocks H1 and H2 is two. -8- ICX424AQ Image Sensor Characteristics Item G Sensitivity Sensitivity comparison Saturation signal Smear Video signal shading Symbol Sg Rr Rb Vsat Sm SHg Min. 600 0.4 0.3 500 -100 -92 20 25 8 8 2 0.5 3.8 3.8 3.8 0.5 Srg Uniformity between video signal channels Sbg Dark signal Dark signal shading Line crawl G Line crawl R Line crawl B Lag Vdt Vdt Lcg Lcr Lcb Lag Typ. 750 0.55 0.45 0.7 0.6 mV dB % % % % mV mV % % % % Max. Unit mV Measurement method 1 1 1 2 3 4 4 5 5 6 7 8 8 8 9 Ta = 60C Ta = 60C Zone 0 and I Zone 0 to II' Ta = 60C (Ta = 25C) Remarks 1/30s accumulation Note) All image sensor characteristic data noted above is for operation in 1/60s progressive scan mode. Zone Definition of Video Signal Shading 659 (H) 12 12 12 H 8 V 10 H 8 494 (V) Zone 0, I Zone II, II' V 10 10 Ignored region Effective pixel region Measurement System CCD signal output [A] Gr/Gb CCD C.D.S AMP S/H R/B S/H R/B channel signal output [C] Gr/Gb channel signal output [B] Note) Adjust the amplifier gain so that the gain between [A] and [B], and between [A] and [C] equals 1. -9- ICX424AQ Image Sensor Characteristics Measurement Method Measurement conditions (1) In the following measurements, the device drive conditions are at the typical values of the bias and clock voltage conditions. (2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical black level (OB) is used as the reference for the signal output, which is taken as the value of the Gr/Gb channel signal output or the R/B channel signal output of the measurement system. Color coding of this image sensor & Readout Gb R Gb R B Gr B Gr Gb R Gb R B Gr B Gr The primary color filters of this image sensor are arranged in the layout shown in the figure on the left (Bayer arrangement). Gr and Gb denote the G signals on the same line as the R signal and the B signal, respectively. Horizontal register Color Coding Diagram All pixels signals are output successively in a 1/60s period. The R signal and Gr signal lines and Gb signal and B signal lines are output successively. - 10 - ICX424AQ Image sensor readout mode The diagram below shows the output methods for the following two readout modes. (1) Progressive scan mode R G R G R VOUT G B G B G 1. Progressive scan mode In this mode, all pixel signals are output in non-interlace format in 1/60s. All pixel signals within the same exposure period are read out simultaneously, making this mode suitable for high resolution image capturing. (2) Center scan mode Undesired portions (Swept by vertical register high-speed transfer) Picture center cut-out portion 2. Center scan mode This is the center scan mode using the progressive scan method. The undesired portions are swept by vertical register high-speed transfer, and the picture center portion is cut out. There are the mode (120 frames/s) which outputs 222 lines of an output line portion, and the mode (240 frames/s) which outputs 76 lines. - 11 - ICX424AQ Definition of standard imaging conditions (1) Standard imaging condition I: Use a pattern box (luminance: 706cd/m2, color temperature of 3200K halogen source) as a subject. (Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter and image at F5.6. The luminous intensity to the sensor receiving surface at this point is defined as the standard sensitivity testing luminous intensity. (2) Standard imaging condition II: Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles. Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted to the value indicated in each testing item by the lens diaphragm. 1. G Sensitivity,sensitivity comparison Set to standard imaging condition I. After setting the electronic shutter mode with a shutter speed of 1/100s, measure the signal outputs (VGr, VGb, VR and VB ) at the center of each Gr, Gb, R and B channel screens, and substitute the values into the following formula. VG = (VGr + VGb)/2 Sg = VG x 100 [mV] 30 Rr = VR/VG Rb = VB/VG 2. Saturation signal Set to standard imaging condition II. After adjusting the luminous intensity to 20 times the intensity with the average value of the Gr signal output, 150mV, measure the minimum values of the Gr, Gb, R and B signal outputs. 3. Smear Set to standard imaging condition II. With the lens diaphragm at F5.6 to F8, first adjust the average value of the Gr signal output to 150mV. Measure the average values of the Gr signal output, Gb signal output, R signal output and B signal output (Gra, Gba, Ra and Ba), and then adjust the luminous intensity to 500 times the intensity with average value of the Gr signal output, 150mV. After the readout clock is stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure the maximum value (Vsm [mV]), independent of the Gr, Gb, R and b signal outputs, and substitute the values into the following formula. Sm = 20 x log Vsm / ( Gra + Gba + Ra + Ba x1x1 4 500 10 ) [dB] (1/10V method conversion value) 4. Video signal shading Set to standard imaging condition II. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity so that the average value of the Gr signal output is 150mV. Then measure the maximum (Grmax [mV]) and minimum (Grmin [mV]) values of the Gr signal output and substitute the values into the following formula. SHg = (Grmax -Grmin)/150 x 100 [%] - 12 - ICX424AQ 5. Uniformity between video signal channels After measuring 4, measure the maximum (Rmax [mV]) and minimum (Rmin [mV]) values of the R signal and the maximum (Bmax [mV]) and minimum (Bmin [mV]) values of the B signal, and substitute the values into the following formula. Srg = | (Rmax - Rmin)/150 | x 100 [%] Sbg = | (Bmax - Bmin)/150 | x 100 [%] 6. Dark signal Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference. 7. Dark signal shading After measuring 6, measure the maximum (Vdmax [mV]) and minimum (Vdmin [mV]) values of the dark signal output and substitute the values into the following formula. Vdt = Vdmax - Vdmin [mV] 8. Line crawls Set to standard imaging condition II. Adjust the luminous intensity so that the average value of the Gr signal output is 150mV, and then insert R, G, and B filters and measure the difference between G signal lines (Glr, Glg, Glb [mV]).as well as the average value of the G signal output (Gar, Gag, Gab). Substitute the values into the following formula. Lci = Gli x 100 [%] (i = w, r, g, b) Gai 9. Lag Adjust the Gr signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) x 100 [%] VD V2 Light Strobe light timing Signal output 150mV Output Vlag (lag) - 13 - Drive Circuit 15V 100k 0.1 -7.5V 1/35V 20 19 18 17 1 2 3 4 5 6 7 8 1000p 2SC4250 0.1 3.3V 1 XSUB 2 XV3 3 4 NC V3 V2 V1 GND GND H2 H1 RG VL SUB GND SUBCIR 9 11 12 XV1 10 16 15 14 13 12 11 10 H2 2200p 0.1 3.3/16V 1M H1 RG VDD - 14 - 15 0.1 14 13 ICX424 (BOTTOM VIEW) XV2 6 7 VOUT CXD3400N CGG XSG3 5 16 0.1 CCD OUT 4.7k 3.3/20V 0.01 9 XSG2 8 ICX424AQ ICX424AQ Spectral Sensitivity Characteristics (Includes lens characteristics, excludes light source characteristics) 1.0 G 0.9 0.8 0.7 Relative Response R B 0.6 0.5 0.4 0.3 0.2 0.1 0 400 450 500 550 Wave Length [nm] 600 650 700 - 15 - Drive Timing Chart (Vertical Sync) Progressive Scan Mode VD "a" 7 508 510 525 1 7 1 2 3 4 5 6 7 8 HD 510 V1 V2 V3 525 1 1 2 3 4 5 6 7 8 1 2 3 OUT 494 1 2 494 1 2 - 16 - ICX424AQ Drive Timing Chart (Vertical Sync "a" Enlarged) Progressive Scan Mode/Center Scand Mode "a" Enlarged H1 V1 520 582 V2 V3 - 17 - 62 50 12 12 12 12 12 12 12 12 12 12 12 12 ICX424AQ Drive Timing Chart (Horizontal Sync) Progressive Scan Mode CLK 35 1 123 125 16 H2 SHP SHD - 18 - 1 36 1 1 12 1 36 1 1 24 1 1 37 1 V1 36 V2 24 V3 36 1 12 SUB 23 1 12 RG 1 72 107 H1 1 780 1 ICX424AQ Drive Timing Chart (Vertical Sync) Center Scan Mode 1 VD "d" 20 21 24 245 246 "a" "b" "c" "d" "a" "b" 261 262 1 2 3 4 5 6 7 8 1 HD 245 246 V1 V2 V3 356 357 136 137 356 357 OUT 1 261 262 1 2 3 4 5 6 7 8 - 19 - ICX424AQ Drive Timing Chart (Horizontal Sync) Center Scan Mode 1 (Frame Shift) ("b") 10920 bits = 14H 35 H1 H2 - 20 - V1 V2 V3 12 12 12 12 12 12 72 12 12 12 12 12 12 #1 #142 ICX424AQ Drive Timing Chart (Horizontal Sync) Center Scan Mode 1 (High-speed Sweep) ("d") 12480 bits = 16H 35 H1 H2 - 21 - V1 V2 V3 12 12 12 12 12 12 72 12 12 12 12 12 12 #1 #167 ICX424AQ Drive Timing Chart (Vertical Sync) Center Scan Mode 2 VD "d" 26 27 30 105 106 "a" "b" "c" "d" "a" "b" 129 130 131 1 2 3 4 5 6 7 8 1 HD 105 106 V1 V2 V3 283 284 209 210 283 284 OUT 1 129 130 131 1 2 3 4 5 6 7 8 - 22 - ICX424AQ Drive Timing Chart (Horizontal Sync) Center Scan Mode 2 (Frame Shift) ("b") 15600 bits = 20H 35 H1 H2 - 23 - V1 V2 V3 12 12 12 12 12 12 72 12 12 12 12 12 12 #1 #215 ICX424AQ Drive Timing Chart (Horizontal Sync) Center Scan Mode 2 (High-speed Sweep) ("d") 18720 bits = 24H 35 H1 H2 V1 V2 V3 12 12 12 12 12 12 72 - 24 - 12 12 12 12 12 12 #1 #255 ICX424AQ ICX424AQ Notes on Handling 1) Static charge prevention CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following protective measures. a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use conductive shoes. b) When handling directly use an earth band. c) Install a conductive mat on the floor or working table to prevent the generation of static electricity. d) Ionized air is recommended for discharge when handling CCD image sensors. e) For the shipment of mounted substrates, use boxes treated for the prevention of static charges. 2) Soldering a) Make sure the package temperature does not exceed 80C. b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a 30W soldering iron with a ground wire and solder each pin in less than 2 seconds. For repairs and remount, cool sufficiently. c) To dismount an image sensor, do not use a solder suction equipment. When using an electric desoldering tool, use a thermal controller of the zero-cross On/Off type and connect it to ground. 3) Dust and dirt protection Image sensors are packed and delivered by taking care of protecting its glass plates from harmful dust and dirt. Clean glass plates with the following operations as required, and use them. a) Perform all assembly operations in a clean room (class 1000 or less). b) Do not either touch glass plates by hand or have any object come in contact with glass surfaces. Should dirt stick to a glass surface, blow it off with an air blower. (For dirt stuck through static electricity ionized air is recommended.) c) Clean with a cotton bud and ethyl alcohol if grease stained. Be careful not to scratch the glass. d) Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when moving to a room with great temperature differences. e) When a protective tape is applied before shipping, just before use remove the tape applied for electrostatic protection. Do not reuse the tape. 4) Installing (attaching) a) Remain within the following limits when applying a static load to the package. Do not apply any load more than 0.7mm inside the outer perimeter of the glass portion, and do not apply any load or impact to limited portions. (This may cause cracks in the package.) Cover glass 50N Plactic package Compressive strength 50N 1.2Nm Torsional strength b) If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate, or an adhesive. - 25 - ICX424AQ c) The adhesive may cause the marking on the rear surface to disappear, especially in case the regulated voltage value is indicated on the rear surface. Therefore, the adhesive should not be applied to this area, and indicated values should be transferred to other locations as a precaution. d) The notch of the package is used for directional index, and that can not be used for reference of fixing. In addition, the cover glass and seal resin may overlap with the notch of the package. e) If the leads are bent repeatedly and metal, etc., clash or rub against the package, the dust may be generated by the fragments of resin. f) Acrylate anaerobic adhesives are generally used to attach CCD image sensors. In addition, cyanoacrylate instantaneous adhesives are sometimes used jointly with acrylate anaerobic adhesives. (reference) 5) Others a) Do not expose to strong light (sun rays) for long periods, color filters will be discolored. When high luminance objects are imaged with the exposure level control by electronic-iris, the luminance of the image-plane may become excessive and discolor of the color filter will possibly be accelerated. In such a case, it is advisable that taking-lens with the automatic-iris and closing of the shutter during the power-off mode should be properly arranged. For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) Brown stains may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. - 26 - Package Outline Unit: mm 16 pin DIP (450mil) A 0 to 9 6.1 9 16 D ~ 2.5 C 11.43 8.4 5.7 V 2-R0.5 ~ 2.5 H 9.5 11.4 0.1 0.5 B' 1.2 3.35 0.15 9.2 2.5 3.1 0.3 M 1.27 3.5 0.3 - 27 - 1. "A" is the center of the effective image area. ~ 2. The two points "B" of the package are the horizontal reference. The point "B'" of the package is the vertical reference. 3. The bottom "C" of the package, and the top of the cover glass "D" are the height reference. 4. The center of the effective image area relative to "B" and "B'" is (H, V) = (6.1, 5.7) 0.15mm. 5. The rotation angle of the effective image area relative to H and V is 1. 6. The height from the bottom "C" to the effective image area is 1.41 0.10mm. The height from the top of the cover glass "D" to the effective image area is 1.94 0.15mm. 7. The tilt of the effective image area relative to the bottom "C" is less than 50m. The tilt of the effective image area relative to the top "D" of the cover glass is less than 50m. 8. The thickness of the cover glass is 0.75mm, and the refractive index is 1.5. 9. The notches on the bottom of the package are used only for directional index, they must not be used for reference of fixing. 0.69 1.27 0.46 0.3 (For the first pin only) PACKAGE STRUCTURE PACKAGE MATERIAL Plastic LEAD TREATMENT GOLD PLATING LEAD MATERIAL 42 ALLOY PACKAGE MASS 0.90g Sony Corporation ICX424AQ DRAWING NUMBER AS-C2.2-01(E) 0.25 1.2 10.3 12.2 0.1 11.6 8 1 2.5 B |
Price & Availability of ICX424AQ
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |